6-Fuse Raised Power Tap Fuse Block (L60-PT6)
If you need to add a few circuits for all of the “extras” that you’ve installed, this Power Tap Fuse Block is the hot ticket. It has a 14 gauge x 24″ long power input lead with ring terminal that feeds all 6 circuits. Rated 30 amps max per fuse and 80 amps total load. Each circuit has a spade screw output and the terminals are provided, as well as the mounting screws. Overall dimensions are 4-7/8″ long x 1-3/8″ wide and 2-1/4″ high including the protective dust cap. For ATO/ATC type fuses. It just doesn’t get much easier or better looking than this.
$39.50
If you need to add a few circuits for all of the “extras” that you’ve installed, this Power Tap Fuse Block is the hot ticket. It has a 14 gauge x 24″ long power input lead with ring terminal that feeds all 6 circuits. Rated 30 amps max per fuse and 80 amps total load. Each circuit has a spade screw output and the terminals are provided, as well as the mounting screws. Overall dimensions are 4-7/8″ long x 1-3/8″ wide and 2-1/4″ high including the protective dust cap. For ATO/ATC type fuses. It just doesn’t get much easier or better looking than this.
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Starter Switch Kit
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′. The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; you’ll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at our RFID unit.
SKU: 12*** -
Hot Rod Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. This is the security system that your hot rod has been missing.
As you may already know the “HOT DOT” ignition takes the place of your conventional “keyed” ignition switch however it has no security built in. This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?
RFID stands for Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna. The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1: High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2: Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it won’t restart.
Mode 3: NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicle’s windows closed. If the vehicle’s windows are open we do not have a measurement for how far away the unit will work. There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID
Related products
-
Hot Rod Wiring Products
LED Conversion Kit
Make any single intensity (BRIGHT ONLY) LED strip dual intensity (DIM and BRIGHT) with one of these conversion kit. You will need one per strip depending on how many LED you have in each light. The L-JE02 Is rated for 25-60 RED LED’s and 12-32 Amber LED’s. The L-JE03 Is rated for 5-20 RED LED’s and 4-8 AMBER LED’s. The L-JE01’s are used for Incandescent bulbs. NOTE These conversion kits are intended for use with our LED strips only. They will work with other manufacturer’s LED’s but we DO NOT guarantee that they will work.
SKU: L-JE0# -
-
Hot Rod Wiring Products
10 Fuse;Fuse Block WI-6010
Each fuse circuit is fed separately. Rated 30 amps max per fuse. Side blade input and output on opposing sides and the terminals are provided, as well as the mounting screws. Overall dimensions are: 7 1/4″ long x 2 1/16″ wide x 2-1/16″ high, including the protective dust cap screw. For ATO/ATC type fuses rated for a max of 150 amps.
SKU: WI-6010
