Radiator Fan Wiring Harness and Thermostat
This is the best “standar” Radiator Fan Harness we could find. Thermostat with 3/8-NPT thread, stainless steel 3/8-to-1/2NPT adaptor, connector, relay, relay socket with wire harness leads, fuse holder, fuse, the necessary hardware for installation and instructions. Turns ON at 195° and OFF at 185°. If you’re putting in an electric fan, this kit will make it operate right.
$118.00
This is the best “standar” Radiator Fan Harness we could find. Thermostat with 3/8-NPT thread, stainless steel 3/8-to-1/2NPT adaptor, connector, relay, relay socket with wire harness leads, fuse holder, fuse, the necessary hardware for installation and instructions. Turns ON at 195° and OFF at 185°. If you’re putting in an electric fan, this kit will make it operate right.
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Starter Switch Kit
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′. The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; you’ll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at our RFID unit.
SKU: 12*** -
Hot Rod Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. This is the security system that your hot rod has been missing.
As you may already know the “HOT DOT” ignition takes the place of your conventional “keyed” ignition switch however it has no security built in. This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?
RFID stands for Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna. The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1: High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2: Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it won’t restart.
Mode 3: NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicle’s windows closed. If the vehicle’s windows are open we do not have a measurement for how far away the unit will work. There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID
Related products
-
Specialty Flashers & Relays
Turn Signal Indicator Diode (V- TSID)
Allows you to use one indicator light (like original VW) to show you that either the left turn, right turn or 4-way flashers are blinking. Both left and right “sides” feed through diodes to feed one light. 1 amp maximum load.
SKU: V- TSID -
Specialty Flashers & Relays
Headlight Reminder Buzzer (32021)
There is nothing as embarrassing to a car guy as a dead battery because you left your lights on. This kit sounds our new Buzzer and the center lights red reminding you your lights are on but the key is either out of the ignition or in the off position. The kit includes the Buzzer, Module, and wiring instructions. Mounts in a 3/4″ hole and the chrome bezel is 7/8″
SKU: 32021 -
Specialty Flashers & Relays
Digital Gear Shift Sending Unit (DK-GSS3000)
Now Self Adjusting!
Dakota Digital’s universal, adjustable gear shift indicator sending unit. Works with GM TH350, TH400, 700R4, 4L60, 4L80, and powerglide; Ford C-4, C-6 and AOD; Mopars and many others. Full electronic adjustability from inside the car – no magnets to align. Built-in neutral safety switch and reverse back-up light circuits. Comes complete with mounting hardware pack, electronic sending unit, and gear shift decoder. Works perfectly with StreetWorks LED Gear Shift Indicator Lights and Combination LED Turn Signal/ High Beam Shifter Indicator Lights.
SKU: DK-GSS2000 -
Specialty Flashers & Relays
Power Cowl Vent Kit (L34)
Give your cowl vent a lift with this powerful gear motor kit that comes complete with gear motor, brackets, hardware, interior switch, wire, connectors, and instructions. Steel bracket for cowl can be bolted or welded. Attractive 5″ aluminum rod arm gives a clean look. Motor with mounting bracket and lever arm measure 2-1/2″ wide, 4″ high and 3-1/4″ deep including motor, not including 5″ connecting arm. Also works for power glove box door.
The motor is not waterproof.
SKU: L34
