Shop
Showing 41–60 of 345 results
-
Remotes & Keyless Entry Systems
Cable Installation Kit for Door Solenoids (L22C)
Why scrounge through hardware stores for the rest of the “kit” that those guys don’t sell? This kit puts together all of the little parts to connect actuators or solenoids to latches… for less than 12 bucks! Includes 30″ of aircraft cable, a delrin® pulley, wire stay, pulley mounting hardware, cable ends and instructions. Don’t waste time and money – get our kit and make your life a little easier.
SKU: L22C (One Door) -
Hot Rod Exterior Lighting, LED Hot Rod Headlights
LED Headlights (251##)
NSRA SAFETY PRODUCT OF THE YEAR 2014
NSRA NEW PRODUCT OF THE YEAR 2014
At every show we attended in 2013 people asked when we would carry LED headlights. We found an excellent product but the lens just looked wrong in most Rods and they were expensive. So we kept looking. By late fall we had a solution that we were testing. We started with a 7″ round glass lens and mated it to an H4 LED. This worked well and the bulb put out a lot of light but it was scattered all over the place. Rather than rush to market we kept looking and it was worth the wait! Finally we found this H4 LED bulb that we are offering here. With a distinct difference between Hi & Lo beams the crisp white light pattern is the best we’ve seen from this configuration. They draw less amps that your old bulbs and plug into your 3 prong socket so you don’t need to upgrade your wiring. Each bulb has a power controller which is permanently attached to the bulb / fan assembly. We’re thrilled to offer this LED headlight package at a realistic price.
These new 7” round Hella Vision Plus lenses use an advanced reflector design and conform to SAE/DOT standards for street and highway use.
7″ Round headlights with H4 style LED bulbs. The lenses have the 3 positioning tabs to make aligning them a snap. From the retaining ring they are 4 1/4″ deep so be sure your buckets will accept the bulb-fan assembly. 25101 Sold in pairs
7″ x 6″ rectangle headlights with H4 style LED bulbs. The lenses should fit right into your existing frames. They are 5″ deep with the LED bulbs in place. 25112 Sold in Pairs
H4 LED bulbs only. Put them into your existing H4 Lenses. 25145 Sold in pairs.
WARNING: Headlight buckets that have springs in the center of the bucket may not be able to accomodate this LED setup without modifications or installing new buckets. These LED bulbs willl not fit King Bee Buckets, and may require some modifications to fit Dietz buckets. Tri-Five vehicles will need to extend their headlight buckets.
SKU: 251## -
Hot Rod Power Window Switches
Single Rectangular Billet Power Window Switch (L39BS#)
Our Billet 3-wire power window rocker switch sits in a billet frame that’s only 1-1/8″ wide by 1-3/4″ high. Adapt directly to positive (+) output remotes – no extra relays required!
Single Switch
Includes: Single switch & frame, polarity reversing module, wire leads and instructions.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39BS# -
Hot Rod Power Window Switches
Double Rectangular Billet Power Window Switch Panel (L39BD#)
Our dual power window rocker switch sits inside an billet frame that’s only 2″ wide by 1-3/4″ high. Adapt directly to positive (+) output remotes – no extra relays required!
Dual Switch
Dual switch kit for center console mounting or for both switches on the driver door only.
Kit includes: Dual switch frame with swithes, (2) polarity reversing modules, wire leads and instructions.
Available with either a dimpled or paddle style rocker. Switch and frame have a brushed aluminum finish.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39BD# -
Hot Rod Power Window Switches
Triple billet Power Window Switch kit (L39BT#)
Triple Switch
Triple kit puts dual switches on the driver door and one on the passenger door. Switches and frames, (2) polarity reversing modules, lots of wire and instructions.
Kit includes: (1)Dual switch frame with switches, (1) single switch & frame, (2) polarity reversing modules, wire leads and instructions.
Available with either a dimpled or paddle style rocker. Switch and frame have a brushed aluminum finish.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39BT# -
Hot Rod Exterior Lighting, LED Hot Rod Headlights
7″ Round Replacement Hella Headlight Lens (25123)
These are the exact same Hella lenses we use in the Award Winning 7″ round LED headlight kits. These lenses conform to SAE/DOT standards for street and highway use. They are glass lenses and retain that original look, fit and function. They do not come with bulbs. The lenses accept a standard H4 style bulb.
SKU: 25123 -
Courtesy Lighting, Hot Rod Exterior Lighting, Hot Rod LED Backup Lights, LED Hot Rod Headlights
Rodders Light Upgrade Package (EL-RLP)
Courtesy Lighting, Hot Rod Exterior Lighting, Hot Rod LED Backup Lights, LED Hot Rod HeadlightsRodders Light Upgrade Package (EL-RLP)
For all you Rodders out there this is a light upgrade package that will add to the safety of your car.
EL-RLP Basic Rod Light Package Upgrade Kit
What You Get:
25101: 1 pair LED Headlights with 7″ round lenses
25012: 1 pair Red 1157 LED replacements for brake lights.
25024: 1 pair Amber 1157 LED replacements for turn signals.
L96WCL: 1 pair White LED backup lights.
EL-MB: 1 Micro Billet LED Third Brake Light.
AM-02R: 1 Pair of electronic LED flashers.
Total retail price if you purchased everything separately: $508.00
Your price when you buy the light upgrade package: $379.00
That’s a total savings of $129.00
EL-RLPD Deluxe Cobra Light Upgrade Kit
What You Get:
25101: 1 pair LED Headlights with 7″ round lenses
25012: 1 pair Red 1157 LED replacements for brake lights.
25024: 1 pair Amber 1157 LED replacements for turn signals.
L63BW: 1 pair White flush mount LED backup lights.
EL-MB: 1 Micro Billet LED Third Brake Light.
AM-02R: 1 Pair of electronic LED flashers.
L03: Trunk light kit with tilt switch and 1 2″ LED strip light.
L04G: Interior courtesy light kit with 2 jamb switches and 2 2″ LED strip lights.
EL-03E: Engine bay light kit includes 1 tilt switch and 3 8″ LED strip lights.
EL-DR: 12″ daytime running light with bracket.
Total retail price if you purchased everything separately: $777.00
Your price when you buy the light upgrade package: $549.00
That’s a total savings of $228.00
SKU: EL-RLP -
Courtesy Lighting, Hot Rod Exterior Lighting, Hot Rod LED Backup Lights
Cobra Light Upgrade Package (EL-CLP)
Courtesy Lighting, Hot Rod Exterior Lighting, Hot Rod LED Backup LightsCobra Light Upgrade Package (EL-CLP)
For all you Cobra owners out there this is a light upgrade package that will add to the safety of your car.
EL-CLP Basic Cobra Light Package Upgrade Kit
What You Get:
25101: 1 pair LED Headlights with 7″ round lenses
25012: 2 pair Red 1157 LED replacements for brake lights.
25024: 1 pair Amber 1157 LED replacements for turn signals.
L96WCL: 1 pair White LED backup lights.
EL-MB: 1 Micro Billet LED Third Brake Light.
AM-02R: 1 Pair of electronic LED flashers.
Total retail price if you purchased everything separately: $553.00
Your price when you buy the light upgrade package: $419.00
That’s a total savings of $134.00
EL-CLPD Deluxe Cobra Light Upgrade Kit
What You Get:
25101: 1 pair LED Headlights with 7″ round lenses
25012: 2 pair Red 1157 LED replacements for brake lights.
25024: 1 pair Amber 1157 LED replacements for turn signals.
L63BW: 1 pair White flush mount LED backup lights.
EL-MB: 1 Micro Billet LED Third Brake Light.
AM-02R: 1 Pair of electronic LED flashers.
L03: Trunk light kit with tilt switch and 1 2″ LED strip light.
L04G: Interior courtesy light kit with 2 jamb switches and 2 2″ LED strip lights.
EL-03E: Engine bay light kit includes 1 tilt switch and 3 8″ LED strip lights.
EL-DR: 12″ daytime running light with bracket.
Total retail price if you purchased everything separately: $822.00
Your price when you buy the light upgrade package: $569.00
That’s a total savings of $253.00
SKU: EL-CLP -
Hot Rod Exterior Lighting
7″ Round Replacement Headlight Buckets (EL-HLB)
Replacement headlight buckets for your 7″ round headlights. These plastic buckets are intended to be used for either a new installation or to replace older rusted out headlight buckets. The chrome retaining ring, new 3 prong sockets and gaskets are included. They mount onto a flat vertical surface. Sold in pairs. A 6.5” dia. hole will be needed to accept the new bucket.
SKU: EL-HLB -
Hot Rod Power Window Switches
Oval Billet Power Window Switches (L39BO)
Our Billet 3-wire rocker switch sits inside an Oval billet frame that’s only 1-5/8″ wide by 2-1/4″ high. Adapt directly to positive (+) output remotes – no extra relays required!
Single Switch
Single switch / frame, polarity reversing module, wire leads and instructions.
Dual Switch
Dual switch kit for center console mounting or for both switches on the driver door only. Dual switch frame is 3-1/8″ wide by 1-5/8″ high, (2) polarity reversing modules, wire leads and instructions.
Triple Switch
Triple kit puts dual switches on the driver door and one on the passenger door. Switches and frames, (2) polarity reversing modules, lots of wire and instructions.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
NOTE:
These are not plug-in replacements for 5-wire switches. Call if you have questions. Reversing modules are needed for power windows. Switches without modules will work for air-ride systems with separate up – down solenoids requiring a positive signal.
SKU: L39BO -
Hot Rod Exterior Lighting
5 3/4″ Round Replacement Headlight Lens (EL-HL5L)
These are the exact same lenses we use in the Award Winning 5 3/4″” round LED headlight kits. These lenses are DOT approved. They are glass lenses and retain that original look, fit and function. They do not come with bulbs. The lenses accept a standard H4 style bulb.
SKU: EL-HL5L -
Hot Rod Power Window Switches, Switch Panels
Rectangular Dimpled Power Window Switch Kit for 3 Regulators
Hot Rod Power Window Switches, Switch PanelsRectangular Dimpled Power Window Switch Kit for 3 Regulators
3 Switch Panel
A single location (console) 3 switch control panel that measures 2 – 3/4″ wide by 1 – 5/8″ high.
Includes 60″ of lead wires, connectors and instructions. The switch frame mounts with (4) blind studs from behind.
Switches are rated at 5 amps max. Please use relays if you’re 5 amps or more. Polarity reversing modules are required for 2 wire non grounded window kits.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39B3X -
Hot Rod Power Window Switches, Switch Panels
Rectangular Paddle Power Window Switch Kit for 3 Regulators (L39B3XP)
Hot Rod Power Window Switches, Switch PanelsRectangular Paddle Power Window Switch Kit for 3 Regulators (L39B3XP)
3 Switch Panel
A single location (console) 3 switch control panel that measures 2 – 3/4″ wide by 1 – 5/8″ high.
Includes 60″ of lead wires, connectors and instructions. The switch frame mounts with (4) blind studs from behind.
Switches are rated at 5 amps max. Please use relays if you’re 5 amps or more. Polarity reversing modules are required for 2 wire non grounded window kits.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39B3XP -
Hot Rod Power Window Switches, Switch Panels
Oval Dimpled Power Window Switch Kit for 3 Regulators (L39BO3X)
Hot Rod Power Window Switches, Switch PanelsOval Dimpled Power Window Switch Kit for 3 Regulators (L39BO3X)
3 Switch Panel
A single location (console) 3 switch control panel that measures 4″ wide by 1 -5/8″ high.
Includes 60″ of lead wires, connectors and instructions. The switch frame mounts with (4) blind studs from behind.
Switches are rated at 5 amps max. Please use relays if you’re 5 amps or more. Polarity reversing modules are required for 2 wire non grounded window kits.
SKU: L39BO3X -
Hot Rod Power Window Switches, Switch Panels
Oval Paddle Power Window Switch Kit for 3 Regulators (L39BO3XP)
Hot Rod Power Window Switches, Switch PanelsOval Paddle Power Window Switch Kit for 3 Regulators (L39BO3XP)
3 Switch Panel
A single location (console) 3 switch control panel that measures 4″ wide by 1 -5/8″ high.
Includes 60″ of lead wires, connectors and instructions. The switch frame mounts with (4) blind studs from behind.
Switches are rated at 5 amps max. Please use relays if you’re 5 amps or more. Polarity reversing modules are required for 2 wire non grounded window kits.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39BO3XP -
Hot Rod Power Window Switches, Switch Panels
Rectangular Dimpled Power Window Switch Kit for 4 Regulators (L39B4X)
Hot Rod Power Window Switches, Switch PanelsRectangular Dimpled Power Window Switch Kit for 4 Regulators (L39B4X)
Now with either Dimpled or Paddle Rockers
Our distinctive Rectangular Switches can be used for a lot more than just power windows. We can custom make a panel for you. We offer Momentary On/Off, On/Center Off/On, or Momentary On/Center Off/Momentary On switches. The panel measures 3 -3/4″ wide by 1-3/4″ high.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
The switches are rated at 5 amps max. If using for POWER WINDOWS you will need a polarity reversing module. Give us a call or email us to find out everything you might need with this switch panel.
SKU: L39B4X -
Hot Rod Power Window Switches, Switch Panels
Rectangular Paddle Power Window Switch Kit for 4 Regulators (L39B4XP)
Hot Rod Power Window Switches, Switch PanelsRectangular Paddle Power Window Switch Kit for 4 Regulators (L39B4XP)
Now with either Dimpled or Paddle Rockers
Our distinctive Rectangular Switches can be used for a lot more than just power windows. We can custom make a panel for you. We offer Momentary On/Off, On/Center Off/On, or Momentary On/Center Off/Momenatry On swicthes. The panel measures 3 -3/4″ wide by 1-3/4″ high.
The switches are rated at 5 amps max. If using for POWER WINDOWS you will need a polarity reversing module. Give us a call or email us to find out everything you might need with this switch panel.
SKU: L39B4XP -
Hot Rod Power Window Switches, Switch Panels
Oval Dimpled Power Window Switch Kit for 4 Regulators (L39BO4X)
Hot Rod Power Window Switches, Switch PanelsOval Dimpled Power Window Switch Kit for 4 Regulators (L39BO4X)
Now with either Dimpled or Paddle Rockers
Our distinctive Oval Switches can be used for a lot more than just power windows. We can custom make a panel for you. We offer Momentary On/Off, On/Center Off/On, or Momentary On/Center Off/Momentary On switches. The panel measures 4-7/8″ wide by 1-5/8″ high.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
The switches are rated at 5 amps max. If using for POWER WINDOWS you will need a polarity reversing module. Give us a call or email us to find out everything you might need with this switch panel.
SKU: L39BO4X -
Hot Rod Power Window Switches, Switch Panels
“Vintage” Oval Billet 5-Switch Custom Panel (L39BVOX)
This is a custom panel. Please contact us before ordering. Price shown is without any relays or modules that you might need.
Designed in conjunction with our friends at Vintage Air, this gorgeous 5-Switch Billet Panel exactly matches the size of their Streamline Gen-II Pro Panel. It measures 5-1/2″ wide X 2-1/2″ high and is available with your choice of switch functions. Just let us know what you want to do and we’ll set it up for you. The switches are rated 5 amps max. so any necessary relays are sold separately. Includes 24″ leads and hardware. Our panel has a fine turned machine finish which you can easily polish if you so desired. Available with either Dimpled or Paddle style rockers (Dimpled Shown). We can custom make a panel for you that uses Momentary On/Off, On/CenterOff/On, or Momentary On)/CenterOff/Momentary On switches.
PLEASE NOTE: A Polarity Reversing Module (Part# L07W-25) is needed for any switch that will be operating Power Windows, Door lock/unlock, or for any Motor that goes Up and Down or In and Out. Call and we will make sure that you get exactly what you need.
SKU: L39-BVOX