LED Headlights (251##)
In stock (can be backordered)
NSRA SAFETY PRODUCT OF THE YEAR 2014
NSRA NEW PRODUCT OF THE YEAR 2014
At every show we attended in 2013 people asked when we would carry LED headlights. We found an excellent product but the lens just looked wrong in most Rods and they were expensive. So we kept looking. By late fall we had a solution that we were testing. We started with a 7″ round glass lens and mated it to an H4 LED. This worked well and the bulb put out a lot of light but it was scattered all over the place. Rather than rush to market we kept looking and it was worth the wait! Finally we found this H4 LED bulb that we are offering here. With a distinct difference between Hi & Lo beams the crisp white light pattern is the best we’ve seen from this configuration. They draw less amps that your old bulbs and plug into your 3 prong socket so you don’t need to upgrade your wiring. Each bulb has a power controller which is permanently attached to the bulb / fan assembly. We’re thrilled to offer this LED headlight package at a realistic price.
These new 7” round Hella Vision Plus lenses use an advanced reflector design and conform to SAE/DOT standards for street and highway use.
7″ Round headlights with H4 style LED bulbs. The lenses have the 3 positioning tabs to make aligning them a snap. From the retaining ring they are 4 1/4″ deep so be sure your buckets will accept the bulb-fan assembly. 25101 Sold in pairs
7″ x 6″ rectangle headlights with H4 style LED bulbs. The lenses should fit right into your existing frames. They are 5″ deep with the LED bulbs in place. 25112 Sold in Pairs
H4 LED bulbs only. Put them into your existing H4 Lenses. 25145 Sold in pairs.
WARNING: Headlight buckets that have springs in the center of the bucket may not be able to accomodate this LED setup without modifications or installing new buckets. These LED bulbs willl not fit King Bee Buckets, and may require some modifications to fit Dietz buckets. Tri-Five vehicles will need to extend their headlight buckets.
$249.00 – $299.00
-
Hot Rod Exterior Lighting, LED Hot Rod Headlights
LED Headlights (251##)
NSRA SAFETY PRODUCT OF THE YEAR 2014
NSRA NEW PRODUCT OF THE YEAR 2014
At every show we attended in 2013 people asked when we would carry LED headlights. We found an excellent product but the lens just looked wrong in most Rods and they were expensive. So we kept looking. By late fall we had a solution that we were testing. We started with a 7″ round glass lens and mated it to an H4 LED. This worked well and the bulb put out a lot of light but it was scattered all over the place. Rather than rush to market we kept looking and it was worth the wait! Finally we found this H4 LED bulb that we are offering here. With a distinct difference between Hi & Lo beams the crisp white light pattern is the best we’ve seen from this configuration. They draw less amps that your old bulbs and plug into your 3 prong socket so you don’t need to upgrade your wiring. Each bulb has a power controller which is permanently attached to the bulb / fan assembly. We’re thrilled to offer this LED headlight package at a realistic price.
These new 7” round Hella Vision Plus lenses use an advanced reflector design and conform to SAE/DOT standards for street and highway use.
7″ Round headlights with H4 style LED bulbs. The lenses have the 3 positioning tabs to make aligning them a snap. From the retaining ring they are 4 1/4″ deep so be sure your buckets will accept the bulb-fan assembly. 25101 Sold in pairs
7″ x 6″ rectangle headlights with H4 style LED bulbs. The lenses should fit right into your existing frames. They are 5″ deep with the LED bulbs in place. 25112 Sold in Pairs
H4 LED bulbs only. Put them into your existing H4 Lenses. 25145 Sold in pairs.
WARNING: Headlight buckets that have springs in the center of the bucket may not be able to accomodate this LED setup without modifications or installing new buckets. These LED bulbs willl not fit King Bee Buckets, and may require some modifications to fit Dietz buckets. Tri-Five vehicles will need to extend their headlight buckets.
SKU: 251## -
Hot Rod Exterior Lighting
7″ Round Replacement Headlight Buckets (EL-HLB)
Replacement headlight buckets for your 7″ round headlights. These plastic buckets are intended to be used for either a new installation or to replace older rusted out headlight buckets. The chrome retaining ring, new 3 prong sockets and gaskets are included. They mount onto a flat vertical surface. Sold in pairs. A 6.5” dia. hole will be needed to accept the new bucket.
SKU: EL-HLB -
Hot Rod Wiring Products
H4 Headlight Harnesses (EL-HLP)
Are your 3 prong headlight haresses tired and falling apart? Pick up a pair of new harnesses with connectors and make sure you never lose your lights at night. Comes with 2 3 prong harnesses pre-wired with pigtails, connectors and instructions.
SKU: EL-HLP
NSRA SAFETY PRODUCT OF THE YEAR 2014
NSRA NEW PRODUCT OF THE YEAR 2014
At every show we attended in 2013 people asked when we would carry LED headlights. We found an excellent product but the lens just looked wrong in most Rods and they were expensive. So we kept looking. By late fall we had a solution that we were testing. We started with a 7″ round glass lens and mated it to an H4 LED. This worked well and the bulb put out a lot of light but it was scattered all over the place. Rather than rush to market we kept looking and it was worth the wait! Finally we found this H4 LED bulb that we are offering here. With a distinct difference between Hi & Lo beams the crisp white light pattern is the best we’ve seen from this configuration. They draw less amps that your old bulbs and plug into your 3 prong socket so you don’t need to upgrade your wiring. Each bulb has a power controller which is permanently attached to the bulb / fan assembly. We’re thrilled to offer this LED headlight package at a realistic price.
These new 7” round Hella Vision Plus lenses use an advanced reflector design and conform to SAE/DOT standards for street and highway use.
7″ Round headlights with H4 style LED bulbs. The lenses have the 3 positioning tabs to make aligning them a snap. From the retaining ring they are 4 1/4″ deep so be sure your buckets will accept the bulb-fan assembly. 25101 Sold in pairs
7″ x 6″ rectangle headlights with H4 style LED bulbs. The lenses should fit right into your existing frames. They are 5″ deep with the LED bulbs in place. 25112 Sold in Pairs
H4 LED bulbs only. Put them into your existing H4 Lenses. 25145 Sold in pairs.
WARNING: Headlight buckets that have springs in the center of the bucket may not be able to accomodate this LED setup without modifications or installing new buckets. These LED bulbs willl not fit King Bee Buckets, and may require some modifications to fit Dietz buckets. Tri-Five vehicles will need to extend their headlight buckets.
https://www.rodauthority.com/news/watsons-streetworks-7-inch-led-headlights-get-even-better/
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
| Size | 7" X 6" Rectangle H4 LED Headlights (25112), 5.75" Round H4 LED Headlights (EL-HL5), 7" Round H4 LED Headlights (25101) |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Starter Switch Kit
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′. The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; you’ll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at our RFID unit.
SKU: 12*** -
Hot Rod Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. This is the security system that your hot rod has been missing.
As you may already know the “HOT DOT” ignition takes the place of your conventional “keyed” ignition switch however it has no security built in. This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?
RFID stands for Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna. The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1: High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2: Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it won’t restart.
Mode 3: NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicle’s windows closed. If the vehicle’s windows are open we do not have a measurement for how far away the unit will work. There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID
Related products
-
Hot Rod Exterior Lighting
Billet Third Brake Light, Clear Lens! L61C
The BEST pedestal 3rd Brake Lights. Clear lens – 15% brighter! 16-5/8″ wide, 3/4″ high (body), 1-1/8″ deep and only 2″ tall including the swivel base. 60 super bright red LED’s. 3 groups of 15-30-15 provide a 30 LED center 3rd brake light and (2) – 15 LED turn signal/brake lights. Or add our LED conversion kits to get taillight and turn/brake or wire them all as one big and bright 3rd brake light. (L61C)
Now also with Amber Turn Signals!
Now get this light with the center 35 red LED’s as a dedicated brake light and each end with 8 super bright amber LED turn signals – really bright and super visible to make your ride safer than ever. (L61CA)
SKU: L61C -
-
Hot Rod Exterior Lighting
1156 White LED White Bulbs, Pair (EL-56W)
Finally, an 1156 LED replacement bulb that can be seen from all directions. These single element bulbs will work in your existing sockets. It comes with 4 bright LEDs on the sides as well as the tip. It measures less than 2 ¼” long by ¾” wide. These LED replacements shine brighter than their original counterparts offering a visually appealing brightness. These LED lights will provide years of trouble free service. Sold in pairs.
SKU: EL-56W -
Hot Rod Exterior Lighting
Bullet Beehive LED Taillights w/ Billet Base (L84)
Beehive lights are now available in large and small sizes
’50’s styling with 21st century technology. Each light has Super Bright Red & Orange LED’s in a Beehive light that has a neat star pattern. Machined Billet Base provides a high-tech finishing touch. Easily mounted to a flat surface using the hardware provided – only three holes needed to install. Dual intensity converter included. Use as a pair or in groups of four or six for that classic taillight look. These lights meet DOT/SAE requirement J592e and are so marked. Sold in pairs.
Overall dimensions for the original large beehives are 2-3/4″ dia. at the base x 2-7/8″ tall. The new small units are 2-1/4″ dia. at the base x 2-1/8″ tall
SKU: L84
