Featured Hot Rod Parts
C4 Relay Pack (WI-C4)
Gear Motor Actuator (WI-29)
For Gator-Jaws and some original latches made after about 1960, these actuators will provide the power needed to trip the latch. This gear motor actuator has 12 pounds of both push and pulling power. With 7/8” of travel you can use it for door locks, trunk latches and more. These will also work for door locks when used with a polarity reversing module (such as our #L07-W). The actuator comes with the mounting and connecting hardware shown. (Actuator measures 5″ long x 2″ High x 1″ Deep) The unit works in both directions so these are great for power lock & unlock doors.
Toggle Battery Disconnect (L27TM)
A mini-momentary toggle switch controls this battery disconnect. It’s easy to install and easy to hide so it’s a perfect theft deterrent. Intended for “Dry” use only, install the toggle inside your ride. Push it once and the battery is connected, ready for use. Push it again and the battery feed is disconnected except for our auxiliary “hot” feed to the clock or computer or other items requiring power for memory. The solenoid is rated 110 amps continuous duty and 750 amps surge. Hardware, wire, connectors and detailed instructions included. There is NO electricity used when this unit is “on”, only when switching between on and off.
Swing Out Cup holder (#43053)
Add a useable hidden cupholder to your hot rod for those thirsty cruise days. The cupholder has the perfect size opening to harness the largest of quickie mart drinks yet still handles your typical water bottle just fine. This billet aluminum swing out design swivels under the dash or even your seat for that tidy hidden look. The cupholder has a moveable latching under support so it is very compact when put away. Stop limiting yourself on what you drink in your car because it doesn’t have a locking lid and add a cupholder today.
Steering Column Trim / Lightning Roll Cage Pass Through (B03N)
Give your steering column the finished look with our machined aluminum trim with heavy duty rubber seal. Made with StreetWorks unique Split ‘n’ Pinned design for easy installation – no column removal required. The ring measures 3.420″ I.D. and 4.800″ O.D. and includes stainless steel mounting screws. The rubber seal has an opening to fit GM and other columns measuring 1-3/4″ to approximately 2-1/8″ diameter. Some trimming may be required for larger diameters. Now with an additional grommet to fit 1-1/2″ diameter columns.
These trim rings also double as a pretty sweet finishing piece for your Ford Lightning roll cage pass through. Of course these will work for virtually any other roll cage pass through you can think of but they are commonly used in the Lightning application.
Power Cowl Vent Kit (L34)
Give your cowl vent a lift with this powerful gear motor kit that comes complete with gear motor, brackets, hardware, interior switch, wire, connectors, and instructions. Steel bracket for cowl can be bolted or welded. Attractive 5″ aluminum rod arm gives a clean look. Motor with mounting bracket and lever arm measure 2-1/2″ wide, 4″ high and 3-1/4″ deep including motor, not including 5″ connecting arm. Also works for power glove box door.
The motor is not waterproof.
LED Indicator Lights (L18)
These “press in” LED indicator lights are small and easy to install. If your looking for a simple LED indicator that is not over powering to your dash then this is what you are looking for. There are 2 sizes available 5/32″ (0.156″) or 1/4″ (0250″) mounting hole.
Steering Column Trim / Lightning Roll Cage Pass Through (B03N)
Give your steering column the finished look with our machined aluminum trim with heavy duty rubber seal. Made with StreetWorks unique Split ‘n’ Pinned design for easy installation – no column removal required. The ring measures 3.420″ I.D. and 4.800″ O.D. and includes stainless steel mounting screws. The rubber seal has an opening to fit GM and other columns measuring 1-3/4″ to approximately 2-1/8″ diameter. Some trimming may be required for larger diameters. Now with an additional grommet to fit 1-1/2″ diameter columns.
These trim rings also double as a pretty sweet finishing piece for your Ford Lightning roll cage pass through. Of course these will work for virtually any other roll cage pass through you can think of but they are commonly used in the Lightning application.
Polarity Reversing Module (#L07W-25)
Power window motors, power trunk lifts, door locks, etc. need to reverse the direction of rotation of the motor in order to work. This is done by reversing the voltage polarity to the motor wire leads. This Reversing Module is needed when you want to use a switch that doesn’t automatically switch (reverse) both the positive and ground to the electric motor (such as a 3-wire switch or remote control).
Just 1/2″ square x 5/8″ wide – small but mighty!
Swing Out Cup holder (#43053)
Add a useable hidden cupholder to your hot rod for those thirsty cruise days. The cupholder has the perfect size opening to harness the largest of quickie mart drinks yet still handles your typical water bottle just fine. This billet aluminum swing out design swivels under the dash or even your seat for that tidy hidden look. The cupholder has a moveable latching under support so it is very compact when put away. Stop limiting yourself on what you drink in your car because it doesn’t have a locking lid and add a cupholder today.
Small Chrome Low Profile LED Indicators (240**)
These beautiful Low profile LED indicator light add a great look to your dash without being big and bulky. They go great with our “Hot Dot” push button switches. They are available in two sizes, Small one is 7/16′ and mounts in a 5/16′ diameter hole. Purchase small indicators shown on the right in the picture on this page.
The large one is 5/8″ and mounts in a 15/32 diameter hole. Easy 2 wire connections will make this indicator light a great addition to you project. To purchase the Large low profile indicators type “Large Chrome Indicator Light” in the search bar.
Water proof LED Strips
These LED strips are encased in clear waterproof plastic so use them where ever you want. They have peal & stick backing and just to be sure we include mounting clips as well. Each flexable strip is 1/2″ wide and about 1/4″ thick. We sell them in lenghts from 2″ to 36″, and they come in 5 colors, red, amber, blue, cool white and warm white. Each light you order has lead wires attached. The strips are marked in 2″ segments (3 LEDs per segment). You can actualy cut them at the marking, attach new leads, seal the ends and you have a 2nd light!
Prices range from just $8.00 for a 2″ strip up to $84.00 for a full 36 inches. Click on the “add to cart” box to select your color & length.
Get creative! From foot box or trunk lights to full blown under car ground effect lighting this is the solution you’ve been looking for.
Trunk Lid Latch (D04)
We’ve seen this neat little latch showing up on some of the most eye-catching rods. Cable release ready receiver measures 2-3/8″ x 3-5/16″ wide. The spring loaded stud is 2-3/4″ long, overall, and the adjustable spring loading helps to pop the trunk lid up. The latch has a built-in safety feature requiring cable tension for the latch to close. The finish is zinc yellow chromate. You’ll have to fabricate brackets/supports for attaching both pieces but we know you can do it!
Low Profile Magnetic Door Jamb Courtesy Switch (SW-04)
Are you tired of that ugly switch on your door jamb for your courtesy lights? Then this is the switch for you. Hide this slick 2 piece switch on the pillar and the other on the door. Both pieces are paintable and mount into a 3/4″ hole. The switch is rated at 2 amps and has a maximum working distance of 3/4″. Switches are sold individually.
Billet Knob Cable Release (CC-UB10)
A straight-forward, attractive machined billet knob with a 120″ cable so you can open your hood or deck lid. Top quality aircraft cable and durable housing may be cut-to-length. Kit includes housing end cap, “no-fray” cable stop and 3 cable clamps.
C4 Relay Pack (WI-C4)
Universal SS Power Window Switches (PW-5), Rectangle
These new power window switches match our new SS family. We include the polarity reversing module so these switches will work with all modern power windows. The lights are a separate circuit so you decide when they are lit. Like our other switches, they are available in brushed, polished or Raven Black anodized finishes. Choose from our dimpled Infinity style or the sharper edged Chiseled rockers to get the perfect look for your build. Switch faces are 2-½” tall, single switches are 1-3/8″ wide and doubles are 2-½”. You will need 1-¾” of back space. Switches come with lead wires, polarity reversing modules, mounting clips and instructions. The triple kit has a double switch on the driver’s door, a single for the passenger and includes cross-over wiring. Use a double alone when center mounting your switches.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
Engraving on the rockers or faceplates is also available. Contact us for polished and engraved pricing.
Hot Rod Parts & Accessories
Your car is already a beauty, but with hot rod parts from Watson’s StreetWorks, you can create a totally custom experience inside and out. Interior or exterior, under the hood or inside the cabin, we have the street rod parts to ensure your car runs smoothly and looks just as smooth doing it.
Add modern luxuries to old classics with push-button ignition systems, power window switches, and accessories like rocker switches and window regulators. Light up the street and your cabin with hot rod lighting including wiring for indicators, switch panels, flashers and more. You can even dress up your doors and trunk with our artfully designed and caringly crafted latches and hinges, or polish off your cabin with finishing touches like interior trim add-ons for dash vents, cup holders and columns. It’s all possible with hot rod accessories from Watson’s StreetWorks.
Looking for a particular name you trust? You’re likely to find it in our Featured Brands section, which includes popular names in a variety of specialized areas, like E-Stopp, Trique, Carolina Custom, Dakota Digital and so much more. You can also check out our other products for security and access solutions like battery disconnects and remote and entry systems. Have questions about which hot rod parts would be right for your ride? Contact the Watson’s StreetWorks team today — we’d be happy to assist you!