Hot Rod Wiring Products
Showing 21–40 of 89 results
-
Hot Rod Wiring Products
3/8โณ Black or Red Power Post 160A Plus 8 Connections (8 X 20A)
- Connect several wire/cablesย to a central locationย
- (8) #8-32 connection points carry up to 20 amps each at 12 VDCย
- Maximum voltage: 48 VDCย
- Connection Post: Stainless steelย
- Conductive Disk: Nickel-plated copper alloyย
- Conductive Nuts: Tin-plated copper alloyย
- Mechanical fastener nuts: Stainless Steelย
- Mounting Center: 2.5″ (63.5mm)ย
SKU: WI-38 -
Hot Rod Wiring Products
4-Fuse Raised Add-on Fuse Blocks L60-4
Each fuse circuit is fed separately. Rated 30 amps max per fuse. Bottom blade input and output and the terminals are provided, as well as the mounting screws. Overall dimensions are: 4 fuse = 2-1/2″ long x 1″ wide x 2-1/4″ high, including the protective dust cap. For ATO/ATC type fuses.
SKU: L60-4 -
Hot Rod Indicators, Relays & Flashers
40 Amp Double Throw Relay SPDT (L07D-40)
40 amp SPDT (double throw) relay that lets you switch between two outputs, ON/ON switching.ย Can be wired as an anti-theft device with a horn alarm feature so that the horn blows if someone tries to start the car without activating the secret circuit or switch.
SKU: L07D-40 -
Hot Rod Indicators, Relays & Flashers
40 Amp Relay with Built-in Fuse L07-40F
40 amp SPST with built-in fuse, included
The easiest way to add a power circuit that we’ve ever seen. Just wire the relay between power and the load, add a control switch to trigger the relay and one ground wire… you’re done! No need to wire in an extra fuse holder, no problems because all of your fuses are already used. And it’s really neat, compact and clean. Size the fuse to your load requirements and the circuit is protected.
SKU: L07-40F -
Hot Rod Indicators, Relays & Flashers
Two Sets of SPDT Relay Wiring (L-RLY2)
2 SPDT RELAYS
When you want to use a remote control with a 5 wire power window type switch these relays will prevent the remote from shorting back through the 5 wire switch.ย Complete with 40 amp relays and wire leads.
SKU: L-RLY2 -
Hot Rod Wiring Products
6-Fuse Raised Add-on Fuse Blocks (L60-6)
Each fuse circuit is fed separately. Rated 30 amps max per fuse. Bottom blade input and output and the terminals are provided, as well as the mounting screws. Overall dimensions are: 6 fuse = 3-3/8″ long x 1″ wide x 2-1/4″ high including the protective dust cap. For ATO/ATC type fuses.
SKU: L60-6 -
Hot Rod Wiring Products
6-Fuse Raised Power Tap Fuse Block (L60-PT6)
If you need to add a few circuits for all of the “extras” that you’ve installed, this Power Tap Fuse Block is the hot ticket. It has a 14 gauge x 24″ long power input lead with ring terminal that feeds all 6 circuits. Rated 30 amps max per fuse and 80 amps total load. Each circuit has a spade screw output and the terminals are provided, as well as the mounting screws. Overall dimensions are 4-7/8″ long x 1-3/8″ wide and 2-1/4″ high including the protective dust cap. For ATO/ATC type fuses. It just doesn’t get much easier or better looking than this.
SKU: L60-PT6 -
Hot Rod Indicators, Relays & Flashers
80 AMP High AMP Circuit or Ignition Switch “Relief” Relay (Accessory Feed) (L07-80)
Hot Rod Indicators, Relays & Flashers80 AMP High AMP Circuit or Ignition Switch “Relief” Relay (Accessory Feed) (L07-80)
Do you realize that the best ignition switches are rated for 30 amps and some for only 15 amps??? And how many amps of accessories are you using? This relay can give a full 80 amps of accessory power and take the load off the ignition switch. Simple hookup (with ring terminals for aftermarket type switches), 10 gauge wire feeds and connectors. Terrific instructions. Also great as a headlight switch relief relay or for any application that you need 80 amps of switching power.
SKU: L07-80 -
Hot Rod Wiring Products
85 Amp Diode (L-85A-DIODE)
Here’s a real problem solver – from StreetWorks, of course. An 85 amp diode to prevent back streaming in a high-amperage circuit such as a radiator fan, tuner amplifier or any other circuit that you want to be fully isolated. Comes with 10 ga wire leads and butt connectors for easy in-line installation. Only 2/10ths of a volt drop across the diode to allow maximum forward voltage….. What a great idea!
SKU: L-85A-DIODE -
-
Specialty Flashers & Relays
Power Cowl Vent Kit (L34)
Give your cowl vent a lift with this powerful gear motor kit that comes complete with gear motor, brackets, hardware, interior switch, wire, connectors, and instructions. Steel bracket for cowl can be bolted or welded. Attractive 5″ aluminum rod arm gives a clean look. Motor with mounting bracket and lever arm measure 2-1/2″ wide, 4″ high and 3-1/4″ deep including motor, not including 5″ connecting arm. Also works for power glove box door.
The motor is not waterproof.
SKU: L34 -
Automotive Battery Disconnect Switches & Kits
Battery Disconnect For Remote Controls (L27R)
Use that extra remote control channel (just one momentary switch) to shut off the battery from outside the car. Push it once and the battery is connected. Push it again and the battery feed is disconnected. Includes our auxiliary “hot” feed to the clock or computer or other items requiring power for memory. The solenoid is rated 110 amps continuous duty and 750 amps surge. Hardware, wire, connectors and detailed instructions included. There is no electricity used when this unit is ON or OFF, only while switching. Remote not included.
SKU: L27R -
Specialty Flashers & Relays
Turn Signal Module (L-TSMOD)
If you have your own turn signal switches but need brake light override circuitry, get our Turn Signal Module. Full instructions and schematic. (NOTE: The Turn Signal Module is already included in all of our Turn Signal Switch Kits.) Wire leads, instructions and schematic. (Uses a single two-prong flasher, not provided.) Turn Signal Module is just 1-1/2″ square X 7/8″ high.
SKU: L-TSMOD -
Hot Rod Wiring Products
Battery Terminal Studs
Jumper Studs:
Extra heavy duty studs. Solid brass contact post is 13/16″ diameter x 1-1/8″ long with marked, colored cover (red for +, black for -) Terminal stud is 3/8-16. Insulator requires a 1-1/4″ hole to install. ย If you need to replace a single post just drop us a line
Jumper Bracket:
From our friends at Sachse Rod Shop. Galvanized 1/8″ steel plate, 5″ long with Jumper Stud holes and mounting holes and screws. Makes installation a no-brainer!ย
SKU: WI-BJS -
Hot Rod Wiring Products
Battery Power Jumper Studs (31032)
Extra heavy duty studs. Solid brass contact post is 13/16″ diameter x 1-1/8″ long with marked, colored cover (red for +, black for -) Terminal stud is 3/8-16. Insulator requires a 1-1/4″ hole to install. Now sold in Sets only here. If you need to replace a single post just drop us a line
SKU: 31032 -
Wire Routing for Hot Rods
Billet Wire Port (B16)
Here is a great way to dress up the area of the firewall where the wiring harness goes through. The Wire Port main body is 2″ dia. with a 1-1/2″ inside dia. and is secured to the firewall around the wire bundle hole with four (4) truss head screws. A 1″ x 13/16″ deep cut-out in the Wire Port body allows the wire bundle to exit close to the firewall (a rubber grommet is included for smaller wire bundles). The body is then capped off with an attractive machined cover which has three (3) ball-milled grooves. The design allows for the wire bundle to be installed before the final attachment of the Wire Port is done. Attractive, functional and at a very reasonable price.
SKU: B16 -
Wire Routing for Hot Rods
Billet Wire Pass-through (B21)
A really attractive way to dress up the area where the wires come through the firewall. Unit measures 1-1/2″ wide X 2″ tall X 1″ deep with a wire exit size of 1″ wide X 3/4″ deep. Blind fastens from behind for that smooth look. Hardware and template included.
SKU: B21 -
Wire Routing for Hot Rods
Billet ECU Wire Pass Through (WI-001)
An attractive cover with machined grooves to dress up where wire bundles pass through the firewall. ย This wire pass through was designed with large Fuel Injection harnesses in mind. ย The pass through comes with a fitted grommet with a 1″ precut split top hole for ease of installation and can be trimmed. ย The grommet can be opened up to a maximum of 1 5/8″ and has relief cuts to assist with trimming. ย The design of the pass through allows this piece to be added onto a completed vehicle with minimum effort.
Overall dimensionsย are 4 5/8″ tallย x 2 1/4″ wide xย 11/32″ deep on top andย 2 1/8″ deep on bottom. ย
Inside dimensions are 3 3/4″ tall x 1 3/4″ wideย x 5/8″ deep on top and 1 15/16″ deep on bottom.
SKU: WI-001
Take Your Vehicle to The Next Level With Hot Rod Wiring Projects
Looking for the best hot rod wiring kits and parts? Whether your latest hot rod electrical project calls for ignition switch systems or battery disconnects, Watson's StreetWorks has the finest hot rod wiring supplies for every kind of vehicle. You've probably put a lot of time into the outward appearance of your hot rod, and maybe now it's time to invest in some hot rod wiring upgrades to boost your enjoyment while cruising โ or to give you some peace of mind by protecting your investment.
Modernize Your Ride With Hot Rod Electrical Upgrades
If you are looking to give your ride a few 21st Century touches, Watson's StreetWorks has a variety of hot rod wiring options to choose from. To protect your car, you may want to try a remote control battery disconnect. With just the simple push of a button, battery disconnects serve as a great theft deterrent. Keeping your classic hot rod authentic may be a priority, but it's hard to argue against adding a keyless entry system. Power door locks and power windows make it much easier and more comfortable to cruise in style. With a simple hot rod wiring kit, we can help you ride in comfort and style, and let you sleep easy knowing your vehicle is safe.
Does Watson's Offer Hot Rod Wiring Harness Kits?
At Watson's StreetWorks, you'll find a wide selection of wiring harness kits for hot rods of all makes and models. We've got harness kits for wipers, radios, heat, cell phone chargers, lights and more, along with universal hot rod wiring harness kits.
Can Wire Routing Help With My Hot Rod Wiring Upgrade?
Wire routing is a quick and easy way to keep your electrical job simple and organized. Routing attaches the hot rod wire bundles to the car's firewall, door or panel. We offer a range of wire pass-throughs and wire looms to keep those unsightly hot rod wires under control.
Can Your Hot Rod Electrical Experts Help Me With Push Button Start?
Watson's StreetWorks has a selection of ignition switches in our online store for you to browse and see if one works for your needs. Our prices are tough to beat, and so is our service. If you have any questions about our ignition switches or any of our hot rod wiring kits, please contact our team of experts who are happy to answer any questions you may have.
Find the High-Quality Hot Rod Wiring Parts You Need at Watson's StreetWorks
Hot rod wiring projects can be complicated. Let Watson's StreetWorks help keep things simple with our full selection of industry-leading hot rod wiring kits and supplies. We have more than 30 years of automotive experience in providing the best hot rod electrical products. If you're not quite sure what you need or if you have any questions, contact our team of experts today. We're always here to help you get the most out of your hot rod.