door
Showing all 17 results
-
Remotes & Keyless Entry Systems
Gear Motor Actuator (WI-29)
For Gator-Jaws and some original latches made after about 1960, these actuators will provide the power needed to trip the latch. This gear motor actuator has 12 pounds of both push and pulling power. With 7/8” of travel you can use it for door locks, trunk latches and more. These will also work for door locks when used with a polarity reversing module (such as our #L07-W). The actuator comes with the mounting and connecting hardware shown. (Actuator measures 5″ long x 2″ High x 1″ Deep) The unit works in both directions so these are great for power lock & unlock doors.
SKU: WI-29 -
Remotes & Keyless Entry Systems
StreetWorks Door Solenoids (L22N)
You want more power. You want fast action. StreetWorks Solenoids have it. They work the way you want, with 40 pounds of pull so they work with original latches. Solenoids, cables, pulleys, connectors, wire hardware and instructions. Solenoid and bracket measure approximately 2-3/4″ wide x 2-1/16″ high (thick) x 4-1/4″ long.
If you need more power than these solenoids have, you have a door problem.
SKU: L22N -
Remotes & Keyless Entry Systems
Cable Installation Kit for Door Solenoids (L22C)
Why scrounge through hardware stores for the rest of the “kit” that those guys don’t sell? This kit puts together all of the little parts to connect actuators or solenoids to latches… for less than 12 bucks! Includes 30″ of aircraft cable, a delrin® pulley, wire stay, pulley mounting hardware, cable ends and instructions. Don’t waste time and money – get our kit and make your life a little easier.
SKU: L22C (One Door) -
Custom Door Hardware, Windows Cranks & Switch Knobs, Custom Hot Rod Window Cranks
Banjo Style Door Handles and Window Cranks (TQ-BJ**)
Custom Door Hardware, Windows Cranks & Switch Knobs, Custom Hot Rod Window CranksBanjo Style Door Handles and Window Cranks (TQ-BJ**)
Trique Manufacturing’s banjo style door handles, window cranks, and vent window cranks are the perfect compliment to any banjo steering wheel. While these handles and window cranks mesh very well in a vehicle equipped with a banjo steering wheel they also have a look that allows them to stand alone as well. These handles represent a modern take on a nostalgic look. Each handle and crank is precisely waterjet cut from stainless steel then polished to a beautiful luster. The base, cap, and knobs are machined billet aluminum and are fully polished as well. Our screw cover caps house a strong magnet that attaches itself to the heads of the mounting screws offering a secure fit while allowing you to remove it later without marring the part. Choose your door handles or window cranks below. Sold in pairs.
· Compliments any banjo steering wheel
· Stainless steel handle Billet aluminum cap and base
· Magnetic cap prevents marring should you have to remove it
· Universal hub fits all handle shafts
· Designed and Made in the USA
· Length of Banjo Door Handle – 5 1/8″
· Length of Banjo Window Crank – 5 1/2″
· Length of Banjo Vent Window Crank – 3 3/4″
· Height of handle base – 3/4″
SKU: TQ-BJ** -
Cables and Cable Releases
Emergency Door Release Kit (TP-BKD-1)
Even the very best electrical entry systems could go bad. This Emergency Door Release Kit gives you the mechanical back-up way to trip the driver door latch and get into your car. Kit contains 8+ feet of encased cable, stainless steel braided door wire loom with billet ends to run the cable through and into the door, billet pull knob with set screw, cable clips and mounting hardware. Easily run into the engine compartment or under a fender well. Why leave yourself unprotected? Made in America by Itsashoka Innovations.
SKU: TP-BKD-1 -
Hot Rod Power Window Switches
Oval Power Window / Door Lock Switch Kit with Dimpled rockers (L39BOTDL)
Hot Rod Power Window SwitchesOval Power Window / Door Lock Switch Kit with Dimpled rockers (L39BOTDL)
This new kit gives you a 3 switch panel for the drivers side so you can control your Driver’s and Passenger windows along with door locks. You will also receive a 2 switch panel for the passenger side that has the ability to control the passenger window and door locks.
This kit includes the necessary crossover wiring, polarity reversing modules, connectors and instructions.
SKU: L39BOTDL -
Custom Door Hardware, Windows Cranks & Switch Knobs
Billet Levers for Car Locks
All of the power and manual safety locks come with a plastic lever for the manual release. But your car has all the billet goodies! Match it all up with these beautiful billet aluminum levers. Fit 1/4″ shaft with set screw.
SKU: B-RHL -
Remotes & Keyless Entry Systems
Booster Spring (L22-BS)
For those really tough original latches that need an extra “boost” to open, these springs will provide a preload on the latch mechanism so that less force is needed to release the latch. 4-1/2″ long zinc plated high-carbon steel springs have 4.40 pounds/inch of force. The cable connector allows you to adjust the pull to your needs.
SKU: L22-BS -
Cables and Cable Releases
Cable Installation Kit for Latch Releases (B20C)
For Two Doors:
Get all the pieces to help you connect your latch and latch release. 6+ feet of cable and sheathing (cut to length for 2-doors), 8 sets of plastic clips, screws and nuts. Compression sleeves (fixed end) and cable adjusters.
SKU: B20C -
Hot Rod Door Latches and Parts
Gator-Jaw Latches (L24)
The standard for replacing old door latches. These “trip” rotory latches meet all Federal Vehicle Safety Standards and are rated for 750 pounds of holding force. The single rotor latch with “L” shaped release lever assures quick release action from either of two directions (down or horizontal). Latch body measures 3-7/8″ x 1-1/4″ x 13/16″ with threaded holes and installs with 1/4-20 fasteners, not included.
SKU: L24 -
-
Wire Routing for Hot Rods
Nylon and Billet Door Wire Looms (TP-NYLON-1/2)
The look of Billet & Black, the door looms are 1/2″ O.D. x 3/8″ I.D. x 7+” effective length. 1 One fixed and one sliding aluminum boss. Plastic lined. 1 Mount into 3/4″ and 5/8″ Diameter holes with set screw secured “quick” collars.
SKU: TP-NYLON-1/2 -
Hot Rod Door Latches and Parts
Gator-Jaw Door Prop Rod (CA-DRP4)
Carolina Custom’s “Slick Rod” for holding doors open at shows. Secure attachment to your Gator-Jaw style latch – one end fits over the striker bolt, the other end “locks” into the latch. Fits any of the three popular sizes of Gator-Jaw latches. The rod itself is stainless steel.
SKU: CA-DRP4 (pair)