Shop
Showing 321–340 of 349 results
-
Automotive Battery Disconnect Switches & Kits
Toggle Battery Disconnect (L27TM)
A mini-momentary toggle switch controls this battery disconnect. It’s easy to install and easy to hide so it’s a perfect theft deterrent. Intended for “Dry” use only, install the toggle inside your ride. Push it once and the battery is connected, ready for use. Push it again and the battery feed is disconnected except for our auxiliary “hot” feed to the clock or computer or other items requiring power for memory. The solenoid is rated 110 amps continuous duty and 750 amps surge. Hardware, wire, connectors and detailed instructions included. There is NO electricity used when this unit is “on”, only when switching between on and off.
SKU: L27TM -
Custom Door Hardware, Windows Cranks & Switch Knobs
Brake Pedal Hole Trim Plate (ET-6510)
From our friends at Sachse Rod Shop. Each piece is 2″ X 4″ with a 1/2″ wide slot. Overlapping feature allows the slot to be 1-1/4″ to 2″ long. 18 gauge steel. Predrilled holes and stainless screws. Helps make installation very simple. (2 plate pieces and 4 screws)
SKU: SA-6510 -
Hot Rod Air Conditioning Vents
Trique MFG. Oval A/C Vent with a Radius Bezel (TQ-AVO)
Trique’s Oval A/C Vents feature a polished billet aluminum housing with polished stainless steel vents that swivel. The housing accepts a standard 2 1/2″ A/C hose. This single A/C vent features a radius bezel. Each A/C vent comes with mounting brackets and hardware.
· Housings are machined from T-6061
· Billet Aluminum and highly polished
· Vanes are waterjet cut from 316 stainless steel and polished for years of use
· Designed, produced, and assembled in the U.S.A.
Dimensions:
· Footprint = 3.2″ X 1.4″
· Bezel = 4.125″ X 1.76″
· Required depth = .8″
SKU: TQ-AVO -
Hot Rod Air Conditioning Vents
Trique MFG. Dual Oval A/C Vent with a Radius Bezel (TQ-AVDO)
Trique’s Dual Oval A/C Vents feature a polished billet aluminum housing with polished stainless steel vents that swivel. The housing accepts two standard 2 1/2″ A/C hoses. This dual A/C vent features a 30 degree angled bezel. Each A/C vent comes with mounting brackets and hardware.
· Housings are machined from T-6061 Billet Aluminum and fully polished
· Vanes are waterjet cut from 316 stainless steel and polished for years of use
· Designed, produced, and assembled in the U.S.A.
Dimensions:
· Footprint = 6″ X 1.5″
· Bezel = 7.5″ X 2″
· Required depth = .8″
· Finish: Polished
· Material: T-6061 Billet Aluminum housing and Stainless Steel vents
· Sold individually
· Matching Oval Single A/C Vents available
SKU: TQ-AVDO -
Hot Rod Air Conditioning Vents
Trique MFG. Triangular A/C Vent with a Radius Bezel (TQ-AVT)
Trique’s Triangular A/C Vents feature a polished billet aluminum housing with polished stainless steel vents that swivel. The housing accepts a standard 2 1/2″ A/C hose. This single A/C vent features a radius bezel that matches our Dual Oval AC Vent. Each A/C vent comes with mounting brackets and hardware.
· Housings are machined from T-6061 Billet Aluminum and highly polished
· Vanes are waterjet cut from 316 stainless steel and polished for years of use
· Designed, produced, and assembled in the U.S.A.
Dimensions:
· Footprint = 2.85″ X 1.5″
· Bezel = 3.97″ X 2″
· Required depth = .8″
· Due to it’s triangular shape these measurements were taken from the longest and tallest part of the vent.
SKU: TQ-AVT -
Hot Rod Air Conditioning Vents
Trique MFG. Rectangular A/C Vent (TQ-AVRE)
Trique’s Rectangular A/C Vents feature a polished billet aluminum housing with polished stainless steel vents that swivel. The housing accepts a standard 2 1/2″ A/C hose. This single A/C vent features a slim bezel making it perfect for those small dashes that may not have room for a larger A/C vent. Each A/C vent comes with mounting brackets and hardware.
· Housings are machined from T-6061 Billet Aluminum and fully polished
· Vanes are waterjet cut from 316 stainless steel and polished for years of use
· Designed, produced, and assembled in the U.S.A.
Dimensions:
· Footprint = 3″ X .938″
· Bezel = 3.5″ X 1.2″
· Required depth = .8″
SKU: TQ-AVRE -
Hot Rod Air Conditioning Vents
Trique MFG. Round A/C Vent with a Radius Bezel (TQ-AVR)
Trique’s Round A/C Vents feature a polished billet aluminum housing with polished stainless steel vents that swivel. The housing accepts a standard 2 1/2″ A/C hose. This single A/C vent features a radius bezel. Each A/C vent comes with mounting brackets and hardware.
· Housings are machined from T-6061 Billet Aluminum and fully polished
· Vanes are waterjet cut from 316 stainless steel and polished for years of use
· Designed, produced, and assembled in the U.S.A.
Dimensions:
· Footprint = 2.3125″
· Bezel = 2.75″
· Required depth = .8″
SKU: TQ-AVR -
Hood and Trunk Latches
Trunk Lid Latch (D04)
We’ve seen this neat little latch showing up on some of the most eye-catching rods. Cable release ready receiver measures 2-3/8″ x 3-5/16″ wide. The spring loaded stud is 2-3/4″ long, overall, and the adjustable spring loading helps to pop the trunk lid up. The latch has a built-in safety feature requiring cable tension for the latch to close. The finish is zinc yellow chromate. You’ll have to fabricate brackets/supports for attaching both pieces but we know you can do it!
SKU: D04 -
Hood and Trunk Latches
Trunk/Hood Latch and Striker (D03)
This little beauty is called a Rotary Claw Latch. It’s spring loaded, “slams” shut just like a bear claw latch and can be used in a variety of applications like trunks and hoods. It is 1.8″ high from the mounting surface to the top, 1.25″ from the mounting surface to the striker center and the attachment holes are 3.25″ center-to-center. The finish is zinc yellow chromate. Latch has cable release mechanism below the mounting surface. Striker included.
SKU: D03 -
Specialty Flashers & Relays
Turn Signal Indicator Diode (V- TSID)
Allows you to use one indicator light (like original VW) to show you that either the left turn, right turn or 4-way flashers are blinking. Both left and right “sides” feed through diodes to feed one light. 1 amp maximum load.
SKU: V- TSID -
Specialty Flashers & Relays
4-Way VW Turn Signal Hazard Wiring (WI-4WX)
If you no longer have the original turn signal/4-way relay module or switch and still are using your original style taillights, this wiring will restore 4-way capability without the expense ($50 – $70!) of a new module and wiring. Also works with our Turn Signal Relay Pack if you are switching to non-separate turn signal/brake lights like 1157 bulb units. Use with your own On/Off switch or see our switch selection above. (switch not included)
SKU: WI-4WX -
Specialty Flashers & Relays
Programmable Electric Fan Controller
Dakota Digital’s PAC-2750 was designed for the ultimate in flexibility, and to be a simple add-on for electric fan(s). l 70 amp relay included. Fully programmable. Will work with your existing water temp gauge, operating from the temperature sending unit already installed! or a dedicated sending unit can be installed. Features fully programmable “fan on” and “fan off” temperatures to suit any application or personal preferences. Can leave the electric fan operating after the engine has been shut down for a user adjustable time. Full digital LED readout for displaying temperature readings and maintaining simple installation. Operating range: 150F – 250F. 3″ X 2.75″ X 1″ thick.
SKU: DK-PAC2750 -
Specialty Flashers & Relays
Radiator Fan Wiring Harness and Thermostat
This is the best “standar” Radiator Fan Harness we could find. Thermostat with 3/8-NPT thread, stainless steel 3/8-to-1/2NPT adaptor, connector, relay, relay socket with wire harness leads, fuse holder, fuse, the necessary hardware for installation and instructions. Turns ON at 195° and OFF at 185°. If you’re putting in an electric fan, this kit will make it operate right.
SKU: SP-195 -
Specialty Flashers & Relays
Spal 10″ High-Performance Puller Radiator Cooling Fan
Spal manufactures these fans from sturdy plastic and they feature a fully sealed waterproof/dustproof motor. Plus, each fan is individually balanced for long life. Spal fans can be mounted to any radiator with universal brackets and shrouds.
Type: High Performance – 12V Puller
Height: 11.93″ (303mm)
Width: 10.60″ (269.2mm)
Depth: 3.76″ (95.4mm)SKU: SP-CF10 -
Specialty Flashers & Relays
Spal 16″ Radiator Puller Cooling Fan
Spal manufactures these fans from sturdy plastic and they feature a fully sealed waterproof/dustproof motor. Plus, each fan is individually balanced for long life. Spal fans can be mounted to any radiator with universal brackets and shrouds.Type: High Performance – 12V Puller
Height: 16.22″ (412mm)
Width: 15.63″ (397mm)
Depth: 3.45″ (88mm)SKU: SP-CF16 -
Specialty Flashers & Relays
Basic Auto Electricity Book (BAEB)
Now in its 10th Printing! If you’re the type of person who can honestly say that you don’t feel comfortable with electrical wiring or, if you can do it but would like to understand it all better, then this book is for you. We’ve upated it with a new section about LED lights. Also contains sections on: What is Electricity? – covering the battery, alternator, voltage regulator, grounding and fuses Designing a simple circuit – selecting components, connectors & terminals, series and parallel circuits, relays Designing an Electrical System, doing circuit tracing Circuit Diagram Ammeter and Volt Meters – hook-up and how to read them Handy relay circuits, Quick Tips…And More! A full 48 pages plus Foldout Circuit Diagram, Plus an 8-1/2″ x 14″ Pullout Wiring Diagram that you can remove and customize to match your own car’s circuits. “Basic auto Electricity” is the best book I have ever seen on wiring a car. It puts everything into perspective in such a way that anybody with a little interest will come away feeling confident that they can do this. It completely does away with any fear because it deals only with pertinent information in a logical step by step method anyone can understand. All my questions were answered in a matter of fact good humored way, and I am for once, surprised in a very good way.” Customer, Harold Hawley
SKU: BAEB -
Custom Marker Lights, Hot Rod Exterior Lighting
Three 1″ Auto Interior LED Lights (L86 Series)
These bright little 3-LED lights have a variety of uses. They are 1″ diameter overall and mount into a 3/4″ diameter hole. Reds and Ambers are SAE/DOT rated as clearance lights. Provided with an optional stainless steel trim ring.
SKU: L86 -
Custom Marker Lights, Hot Rod Exterior Lighting
6-LED Interior and Marker Lights, L96 Series
Great little 6-LED lights have a variety of uses. They are 1-13/16” diameter overall and mount in a 1-3/8” diameter hole. Red and ambers are SAE/DOT rated as clearance lights. Provided with an optional stainless steel trim ring.
SKU: L96 -
Hot Rod Exterior Lighting
LED Light’N Boltz License Plate Light Assembly Kit
Polished Stainless Steel Dome-head bolts with LED’s to illuminate your license plate. 5/16-18 x 3/4″ threaded bolts. 2 dome-head mounting/illumination bolts with LED’s plus 2 button-head mounting bolts without LED’s. Includes nuts, wire leads. 12 vdc. Set of four as shown. From Design Engineering Inc.
SKU: DE-LNB4
