Custom Hot Rod Switches
Showing 61–76 of 76 results
-
Custom Switches for Hot Rods
LED Dimmer and Knob
All new LED on/off and full range dimmer rated at 6 amps max and no minimum amount of draw is required. ย This dimmerย works with incandescent bulbs and LED’s.ย Dim either LED, incandescent or both types of lighting simultaneously with this one dimmer.ย The dimmer comes with theย knob shown however it will takeย any knob with a 1/4โ shaft.ย Requires wiring both the power and ground leads through the unit for operation.
SKU: WI-DIM -
Custom Switches for Hot Rods
PressTech Touch Pad Switch (L32PS)
A brand new way to activate door solenoids or actuators. This small, 1″ x 1″ x 1/8″ thick pad switch can be hidden in the neatest places. Put it under upholstery, inside a fender lip or mirror housing, almost anywhere and activate it with a simple press. Fully waterproof pad switch comes with quality 3M tape for mounting.
Please Note: If using solenoids or for loads over 2 amps, see our relay section part #L07-40.
Remember – Keylock security can be used with any Entry Triggering Systems.
SKU: L32PS -
Automotive Switches and Buttons
Push Button LED Switch Panel
Please call us with your needs and we will make your custom switch panel for you.ย Virtually any configuration imaginable within our panel sizesย are possible from momentary to standard toggle.
These switches can not currently be purchased online at this time due to there being way too many options available.ย Push Button Panels with LED’s.ย Dimensions are the same as Push Button Panels.ย Your choice of Red, Green, Blue or Amber LED’s.ย We can also do manual and self-canceling turn signal kits with or without LED’s for turn and/or high beam indicators.
Give us a call today!
866-859-0513
SKU: L10R-Panels -
Automotive Switches and Buttons
Waterproof Button Switch (L65BS)
High quality waterproof button for activating solenoids or actuators. Don’t use unsealed switches! The buttons are 5/8″ dia. x 1/4″ tall and mount in a 1/2″ hole, momentary action. 5 amps rating.
Please Note: If using solenoids or for loads over 5 amps, see our relay Part #L07-40.
SKU: L65BS -
-
Hot Rod Power Window Switches
Light Clip for L39B Switches (L39B-Clip)
Now you can add illumination to any of our family of L39B Power Window and specialty switches. This Clip secures to the switch frame mounting screws and holds your choice of 5/32″ size LED (alsoย sold separately). The LED shines between the billet rocker and face plate of the switch. We recommend using oneย clips on each side of theย switch, for example for aย L39BODย switch panel witch is a 2 switch panelย using 3 clips would project an equal amount of light across the panel.
SKU: L39B-Clip -
Hot Rod Power Window Switches
Express Power Window Module (PW-EXP)
Now you can enjoy the convenience of โone touchโ windows on your vehicle. This compact unit mounts inside your door and works with all polarity reversing motors. Simply tap your switch once and the window travels all the way up or down. While in motion just give the switch another tap to stop mid-way. This works with your remote too! Each express module comes with connectors, heavy duty mounting tape and instructions. Each 3″ by 2″ by 1″ module operates one window.
SKU: PW-EXP -
-
Automotive Switches and Buttons
Mini-Rocker Switch (L55)
A sweet little jet black rocker switch with different versions to give you lots of options. The switch measures just 19/32″ x 13/16″ and is rated 5 amps max. except as noted.
Space doesn’t allow us to list all the possible things that we can do with these switches but if you can think it, we can probably do it, including … power window switch, power door locks, power trunk lift, turn signals, self-canceling turn signals, headlight – park lights, etc. Or just add one of our 40 amp relays to increase the circuit switching amperage.
SKU: L55 -
Custom Switches for Hot Rods
Classic Button Style Brake Switch (33021)
Weโre famous for our simple adjustable lever brake switch but they wonโt work on every car so we now offer this simple button style switch.ย You set this up so that the pedal arm pushes on the button when the pedal is at rest. As the pedal moves the button releases completing your brake light circuit. This plastic switch has 1โ of adjustment and is 3โ inches long by ยพโ in diam.ย Mounts in a ยฝโ hole on your bracket.
SKU: 33021 -
Hot Rod Power Window Switches
Power Window Lift Kit by Specialty Power Windows (PW-L2P)
This universal, flat glass kit including OEM motors, rugged risers, motor plug and leads, bottom window channels and mounting material, support brackets, and instructions. 8-1/2″ clearance is needed below the bottom of the glass. Riser can be shortened for your application. Lifetime Warranty from Specialty Power Windows. 2-doors. Works with any of StreetWorks Power Window Switch Kits.
Why buy a kit with plastic switches that you don’t want – pay more and have to throw them away?!?! Get this kit and add the switches that you want. This kit works with all flat glass applications.ย If your ride has curved glass just get in touch, we’ll contact Specialty Power windows and get just what you need.
SKU: PW-L2P -
Custom Switches for Hot Rods
The Best Brake Switch (L08)
We call it that because our customers say it’s the best. This adjustable, mechanical switch helps you by getting rid of those undependable hydraulic pressure switches that burn out every year (or more often!). This switch will last because it uses self-cleaning contacts to prevent the carbon build-up that destroys hydraulic switches. Its adjustable design allows it to fit most pre-1960 vehicles, customs and many other later models with through-the-floor brake pedals, no additional brackets needed. And it’s waterproof. Stainless hardware, connectors and instructions included.
SKU: L08 -
Custom Switches for Hot Rods
700R4 Lock-up Kit
700R4 Brake Switch/lock-up Got a 700R4 transmission? Got a light car and lots of power? Want to have that 700R4 convertor locked up at all times except when the brake switch is on? Here you go. Our Best Brake Switch with a SPDT relay -when the brakes are off the convertor is locked up, and when they’re on, it’s not. Just that simple and easy to install.
SKU: L08-700R4 -
-
Custom Switches for Hot Rods
2 speed plus intermittent wiper Kit Specialty Power Windows (67022)
This flex shaft (cable) wiper system is a great solution for Street Rods and customs being built.ย This universal Dual-Wiper Drive Kit has two wiper shafts that will accept arms that fit 1/2 inch fine spline knurls or arms that fit 1/4 inch shafts. The output shafts are driven by a remote mounted commercial duty 2 speed wiper motor.
This motor has 300 in. lbs. stall torque. The sweep is adjustable from 90 degrees to 160 degrees in 10 degree increments. (Both wipers will sweep the same amount). This dual wiper kit has 2-speed intermittent self-park switch. ย included and will accept many of our knobs.
This kit is best SUITED FOR CARS UNDER CONSTRUCTION. Some applications will require modifications to the original wiper shaft holes. Comes with written and video instructions. (Kits Do Not Include Arms and Blades) Standard kits come with a 72″ drive cable.
SKU: 67022
Customize Your Automotive Switch Panel With Custom Hot Rod Switches
You've reupholstered the seats, updated the safety equipment and made the outside shine like the day it drove off the lot โ now it's time to finish up the interior of your hot rod with custom car switches. Achieve the look you want in your automotive switch panel with custom switches from Watson's StreetWorks. Hot rod switches give you the functionality you want while remaining true to the classic style of your hot rod. Of course, you'll have plenty of different options to choose from โ especially compared to the automotive switches that existed when the manufacturer built your hot rod. Whether you're in the market for crank handle switches or need proper specialty switches, we can build custom automotive switches to control just about anything in your ride. Here at Watson's, our aftermarket switches are built for both durability and functionality using top-rated, premium materials that match the strength and style of your hot rod. Put the finishing touches on your hot rod's interior today with custom car switches from Watson's StreetWorks.
Custom Automotive Switches Upgrade Your Hot Rod to the 21st Century
When it comes time to update your automotive switch panel, you have plenty of options to choose from with custom switches from Watson's StreetWorks. To begin, you need to know what you want to control with your hot rod switches. Choose from functions such as ignition/start, headlights, park lights, wipers and more. Aftermarket switches come in tons of different styles as well โ there are many ways you can match the style of your hot rod. You can select custom car switches such as toggle, push-button, rocker or slide switches. Of course, with your hot rod, the small details matter the most. That's why we also give you the option to choose the finish of your automotive switches with all kinds of colors like metallic billet, black and more. When it comes to getting the right look for your custom automotive switches, we make an effort to make sure you get exactly what you need.
Do Your Hot Rod Switches Come With Wiring Assemblies?
When you buy custom automotive switches from Watson's StreetWorks, you're getting more than the switch itself. Our products come with the wiring assemblies needed to get your custom car switches fully installed and working to total capacity. You'll also receive a detailed set of installation instructions.
Can You Engrave My Custom Toggle Switches?
Depending on the type of custom automotive switches you purchase, we offer the option to engrave them with whatever you would like. When we say custom, we mean it. Whether it's simple writing or a specific simple picture you have in mind, we want your custom hot rod switch to match your exact needs.
Do You Offer Illuminated Aftermarket Switches?
Watson's StreetWorks offers both illuminated and non-illuminated hot rod switches. Whether you're restoring your hot rod for car shows or full driving capabilities (including night driving), we have the custom switches that can make your drives easier to navigate.
Find Top-Rated Custom Hot Rod Switches at Watson's StreetWorks
Whether you're looking for one custom automotive switch for a specific purpose or need a full hot rod switch panel for multiple purposes, Watson's StreetWorks is the best in the industry. Our 30+ years of automotive experience allow us to build the perfect custom car switch to meet your exact needs. Update your interior with custom hot rod switches today. If you have any questions about our products, feel free to contact us. Our dedicated team of experts is always available to help.