latches
Showing all 13 results
-
Remotes & Keyless Entry Systems
Gear Motor Actuator (WI-29)
For Gator-Jaws and some original latches made after about 1960, these actuators will provide the power needed to trip the latch. This gear motor actuator has 12 pounds of both push and pulling power.ย With 7/8โ of travel you can use it for door locks, trunk latches and more. These will also work for door locks when used with a polarity reversing module (such as our #L07-W). The actuator comes with the mounting and connecting hardware shown. (Actuator measures 5โณ long x 2โณ High x 1โณ Deep) The unit works in both directions so these are great for power lock & unlock doors.
SKU: WI-29 -
Remotes & Keyless Entry Systems
StreetWorks Door Solenoids (L22N)
You want more power. You want fast action. StreetWorks Solenoids have it. They work the way you want, with 40 pounds of pull so they work with original latches. Solenoids, cables, pulleys, connectors, wire hardware and instructions. Solenoid and bracket measure approximately 2-3/4″ wide x 2-1/16″ high (thick) x 4-1/4″ long.
If you need more power than these solenoids have, you have a door problem.
SKU: L22N -
Remotes & Keyless Entry Systems
Cable Installation Kit for Door Solenoids (L22C)
Why scrounge through hardware stores for the rest of the “kit” that those guys don’t sell? This kit puts together all of the little parts to connect actuators or solenoids to latches… for less than 12ย bucks! Includes 30″ of aircraft cable, a delrinยฎย pulley, wire stay, pulley mounting hardware, cable ends and instructions. Don’t waste time and money – get our kit and make your life a little easier.
SKU: L22C (One Door) -
Custom Door Hardware, Windows Cranks & Switch Knobs
Billet Levers for Car Locks
All of the power and manual safety locks come with a plastic lever for the manual release. But your car has all the billet goodies! Match it all up with these beautiful billet aluminum levers. Fit 1/4″ shaft with set screw.
SKU: B-RHL -
Remotes & Keyless Entry Systems
Booster Spring (L22-BS)
For those really tough original latches that need an extra “boost” to open, these springs will provide a preload on the latch mechanism so that less force is needed to release the latch. 4-1/2″ long zinc plated high-carbon steel springs have 4.40 pounds/inch of force. The cable connector allows you to adjust the pull to your needs.
SKU: L22-BS -
Automotive Door Latches & Parts
Gator-Jaw Latches (L24)
The standard for replacing old door latches. These “trip” rotory latches meet all Federal Vehicle Safety Standards and are rated for 750 pounds of holding force. The single rotor latch with “L” shaped release lever assures quick release action from either of two directions (down or horizontal). Latch body measures 3-7/8″ x 1-1/4″ x 13/16″ with threaded holes and installs with 1/4-20 fasteners, not included.
SKU: L24 -
Automotive Door Latches & Parts
Gator-Jaw Medium weld in plates (L24M)
Weld these plates to your door to give a strong, solid mounting point for your latches. Installation screws – 1/4-20 x 3/4 S/S button socket screws. Available for either full size gator jaws or our mini’s. Sold in pairs.
SKU: L24M -
Automotive Door Latches & Parts
Gator-Jaw Door Prop Rod (CA-DRP4)
Carolina Custom’s “Slick Rod” for holding doors open at shows. Secure attachment to your Gator-Jaw style latch – one end fits over the striker bolt, the other end “locks” into the latch. Fits any of the three popular sizes of Gator-Jaw latches. The rod itself is stainless steel.
SKU: CA-DRP4 (pair) -
Hood and Trunk Latches
Trunk Lid Latch (D04)
We’ve seen this neat little latch showing up on some of the most eye-catching rods. Cable release ready receiver measures 2-3/8″ x 3-5/16″ wide. The spring loaded stud is 2-3/4″ long, overall, and the adjustable spring loading helps to pop the trunk lid up. The latch has a built-in safety feature requiring cable tension for the latch to close. The finish is zinc yellow chromate. You’ll have to fabricate brackets/supports for attaching both pieces but we know you can do it!
SKU: D04 -
Hood and Trunk Latches
Trunk/Hood Latch and Striker (D03)
This little beauty is called a Rotary Claw Latch. It’s spring loaded, “slams” shut just like a bear claw latch and can be used in a variety of applications like trunks and hoods. It is 1.8″ high from the mounting surface to the top, 1.25″ from the mounting surface to the striker center and the attachment holes are 3.25″ center-to-center. The finish is zinc yellow chromate. Latch has cable release mechanism below the mounting surface. Striker included.
SKU: D03
