Power Door Lock and Window Switch Kit with Dimpled Rockers (L39BTDL)
This kit gives you a rectangle 3 switch panel for the drivers door to control both front windows and door locks. You will also receive a 2 switch panel for the passenger door to control the passenger window and door locks. This kit includes the necessary crossover wiring, switch pigtails, connectors and instructions.
$389.00
This kit gives you a rectangle 3 switch panel for the drivers door to control both front windows and door locks. You will also receive a 2 switch panel for the passenger door to control the passenger window and door locks. This kit includes the necessary crossover wiring, switch pigtails, connectors and instructions.
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Start Ignition Switch
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′. The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; you’ll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at our RFID unit.
SKU: 12*** -
RFID Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. This is the security system that your hot rod has been missing.
As you may already know the “HOT DOT” ignition takes the place of your conventional “keyed” ignition switch however it has no security built in. This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?
RFID stands for Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna. The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1: High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2: Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it won’t restart.
Mode 3: NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicle’s windows closed. If the vehicle’s windows are open we do not have a measurement for how far away the unit will work. There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID -
Wire Routing for Hot Rods
Stainless Steel Braided Door Wire Looms for Suicide Doors (TP-SUICIDE)
These wire looms can open to more than 200 degrees and not bind! Swivel ball bushings assure smooth operation. 1 1/2″ O.D. X 3/8″ I.D. X 7+” length, plastic lined S/S Braid. New Quick Collar ends. Ball swivel flange end mounts vertically and is just 2″ high.
SKU: TP-SUICIDE
Related products
-
Hot Rod Power Window Switches
Oval Billet Power Window Toggle Switch
Our Billet 3-wire rocker switch sits inside an Oval billet frame that’s only 1-5/8″ wide by 2-1/4″ high. Adapt directly to positive (+) output remotes – no extra relays required!
Single Switch
Single switch / frame, polarity reversing module, wire leads and instructions.
Dual Switch
Dual switch kit for center console mounting or for both switches on the driver door only. Dual switch frame is 3-1/8″ wide by 1-5/8″ high, (2) polarity reversing modules, wire leads and instructions.
Triple Switch
Triple kit puts dual switches on the driver door and one on the passenger door. Switches and frames, (2) polarity reversing modules, lots of wire and instructions.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
NOTE:
These are not plug-in replacements for 5-wire switches. Call if you have questions. Reversing modules are needed for power windows. Switches without modules will work for air-ride systems with separate up – down solenoids requiring a positive signal.
SKU: L39BO -
Hot Rod Power Window Switches
Light Clip for L39B Switches (L39B-Clip)
Now you can add illumination to any of our family of L39B Power Window and specialty switches. This Clip secures to the switch frame mounting screws and holds your choice of 5/32″ size LED (also sold separately). The LED shines between the billet rocker and face plate of the switch. We recommend using one clips on each side of the switch, for example for a L39BOD switch panel witch is a 2 switch panel using 3 clips would project an equal amount of light across the panel.
SKU: L39B-Clip -
Hot Rod Power Window Switches
GT2 Power Window Switch
These are our all new GT2 switches. These switches are sold for use as a power window switch however can be used for virtually anything UPON REQUEST. These all new switches have a slim fit and finish to prevent getting snagged when mounted on the door or console of your vehicle. They have the same design as the GT3 and GT4D panels so they will match the rest of your switches.
IF YOU ARE WIRING A 2 SWITCH PANEL ON THE DRIVERS DOOR AND A SINGLE SWITCH PANEL ON THE PASSENGER DOOR ORDER THE TRIPLE KIT.
Single GT2 switch with reversing module 10219……$ 120.00
Double GT2 switch with reversing module 10220……$220.00
Triple kit GT2 (Comes with a Double and a Single panel with reversing modules) 10231…..$320.00
The modular design of the switch face lets us build you a custom switch panel to control just about anything. Whether you want a single switch to turn on a dome light or a bank of 20 to run everything in the car we can do it.
The switches are all machined from billet aluminum and have a brushed finish. The actual switch can be either momentary-off-momentary or on-off-on. All switches are rated at 5 amps so you may want relays for heavy loads. (see page 41) Want lights? We can add 1 or 2 lights to each switch in your choice of colors. The switch panels are 1 3/4” tall. A single switch is 1 5/8” long. Each additional switch adds 1 1/8”. (for example a 6 switch panel is 7 3/8” long) The toggle is 5/8” tall.
The GT4D series include the dividers to safeguard those important circuits from accidentally being switched. The GT3 series are without dividers. The GT2 series switches are without dividers have a short rocker so to not interfere while on your door and include polarity reversing modules(intended for power windows / locks but we can still make these however you would like).
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: GT2 -
Custom Hot Rod Switch Panels, Hot Rod Power Window Switches
Rectangular Paddle Power Window Switch Kit for 3 Regulators (L39B3XP)
Custom Hot Rod Switch Panels, Hot Rod Power Window SwitchesRectangular Paddle Power Window Switch Kit for 3 Regulators (L39B3XP)
3 Switch Panel
A single location (console) 3 switch control panel that measures 2 – 3/4″ wide by 1 – 5/8″ high.
Includes 60″ of lead wires, connectors and instructions. The switch frame mounts with (4) blind studs from behind.
Switches are rated at 5 amps max. Please use relays if you’re 5 amps or more. Polarity reversing modules are required for 2 wire non grounded window kits.
Don’t know if you have Polarity reversing Motors? See the Product Instructions Tab to determine if your motors are Polarity reversing or Non-Polarity reversing.
SKU: L39B3XP
