Gator-Jaw Latches (L24)
The standard for replacing old door latches. These “trip” rotory latches meet all Federal Vehicle Safety Standards and are rated for 750 pounds of holding force. The single rotor latch with “L” shaped release lever assures quick release action from either of two directions (down or horizontal). Latch body measures 3-7/8″ x 1-1/4″ x 13/16″ with threaded holes and installs with 1/4-20 fasteners, not included.
$33.00 – $64.00
The standard for replacing old door latches. These “trip” rotory latches meet all Federal Vehicle Safety Standards and are rated for 750 pounds of holding force. The single rotor latch with “L” shaped release lever assures quick release action from either of two directions (down or horizontal). Latch body measures 3-7/8″ x 1-1/4″ x 13/16″ with threaded holes and installs with 1/4-20 fasteners, not included.
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
| L24: | L24: Mounting Plates with screws,Pair (L24M), Latch & Striker Bolt Pair (L24), Latch & Striker Bolt Single (Right) (L24S-R), Latch & Striker Bolt Single (Left) (L24S-L) |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Starter Switch Kit
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′.ย ย The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; youโll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at ourย RFID unit.
SKU: 12*** -
Hot Rod Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. ย This is the security system that your hot rod has been missing.
As you may already know the โHOT DOTโ ignition takes the place of your conventional โkeyedโ ignition switch however it has no security built in.ย This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?ย
RFID stands forย Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna.ย The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1:ย High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2:ย Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it wonโt restart.
Mode 3:ย NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicleโs windows closed.ย If the vehicleโs windows are open we do not have a measurement for how far away the unit will work. ย There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID
Related products
-
Remotes & Keyless Entry Systems
Gear Motor Actuator (WI-29)
For Gator-Jaws and some original latches made after about 1960, these actuators will provide the power needed to trip the latch. This gear motor actuator has 12 pounds of both push and pulling power.ย With 7/8โ of travel you can use it for door locks, trunk latches and more. These will also work for door locks when used with a polarity reversing module (such as our #L07-W). The actuator comes with the mounting and connecting hardware shown. (Actuator measures 5โณ long x 2โณ High x 1โณ Deep) The unit works in both directions so these are great for power lock & unlock doors.
SKU: WI-29 -
Automotive Door Latches & Parts
Power Door Locks (Pair) (CA-PDL)
Carolina Custom’s Power Door Locks
They’re constructed from aircraft quality aluminum and have stainless steel lock pins and mounting hardware for optimum performance and reliability. Slim 1-3/8″ thick x 2″ tall x 8″ long. Built-in micro switches allows you to use a warning light (LED included). May be installed in doors or kick panel area. Great for suicide doors or if you have installed bear claw latches which cannot be locked otherwise.SKU: CA-PDL -
Automotive Door Latches & Parts
Manual Safety Lock Pins
Carolina Custom’s Manual Safety Lock Pins
They’re constructed from aircraft quality aluminum and have stainless steel lock pins and mounting hardware for optimum performance and reliability. Slim 1″ thick x 2″ tall x 3-1/2″ long. Built-in micro switches allow you to use a warning light (LED included). May be installed in doors or kick panel area. Great for suicide doors.
SKU: CA-MSP -
Remotes & Keyless Entry Systems
StreetWorks Door Solenoids (L22N)
You want more power. You want fast action. StreetWorks Solenoids have it. They work the way you want, with 40 pounds of pull so they work with original latches. Solenoids, cables, pulleys, connectors, wire hardware and instructions. Solenoid and bracket measure approximately 2-3/4″ wide x 2-1/16″ high (thick) x 4-1/4″ long.
If you need more power than these solenoids have, you have a door problem.
SKU: L22N
