Emergency Door Release Kit (TP-BKD-1)
Even the very best electrical entry systems could go bad. This Emergency Door Release Kit gives you the mechanical back-up way to trip the driver door latch and get into your car. Kit contains 8+ feet of encased cable, stainless steel braided door wire loom with billet ends to run the cable through and into the door, billet pull knob with set screw, cable clips and mounting hardware. Easily run into the engine compartment or under a fender well. Why leave yourself unprotected? Made in America by Itsashoka Innovations.
$49.00
Even the very best electrical entry systems could go bad. This Emergency Door Release Kit gives you the mechanical back-up way to trip the driver door latch and get into your car. Kit contains 8+ feet of encased cable, stainless steel braided door wire loom with billet ends to run the cable through and into the door, billet pull knob with set screw, cable clips and mounting hardware. Easily run into the engine compartment or under a fender well. Why leave yourself unprotected? Made in America by Itsashoka Innovations.
| Weight | 0.00000000 lbs |
|---|---|
| Dimensions | 0.00000000 × 0.00000000 × 0.00000000 cm |
You may also like…
-
Hot Rod Ignition Switch Systems
Hot Rod Push Button Starter Switch Kit
Push our Ignition Switch button once and your accessory circuit comes on. A second push and hold engages the starter. When your engine starts just release the switch and your running as well as the LED indicator ring. Press it once more and everything turns off. This gorgeous Stainless steel (22MM) switch mounts in a 7/8″ diameter hole with the overall size of 1′. The compact ignition module can hide under your dash or in the engine bay.
This kit will work with our smaller (16MM) momentary push button but be warned guys; you’ll be using your pinky.
Compare our price to any other Single Switch Ignition System anywhere! We were the first to bring this system to the street rod market and we know how to do it best!
Check out our full line of matching low profile, push button switches and indicator lights.
Note this unit requires securing your car. Check out our battery disconnects or simply install a hidden kill switch or, look at our RFID unit.
SKU: 12*** -
Hot Rod Ignition Security Systems
RFID Ignition Security Unit
This all new StreetWorks RFID is designed to work with your Hot Dot Ignition Systems or your existing key. This is the security system that your hot rod has been missing.
As you may already know the “HOT DOT” ignition takes the place of your conventional “keyed” ignition switch however it has no security built in. This all new RFID Security system gives you the security and convenience that today’s society demands.
What is RFID?
RFID stands for Radio-Frequency Identification. The acronym refers to small electronic devices that consist of a small chip and an antenna. The RFID device serves the same purpose as magnetic strip on the back of a credit card; it provides a unique identifier for that object. And, just as a magnetic strip must be scanned to get the information, the RFID device must be scanned to retrieve the identifying information.
The RFID unit has 3 different operating modes.
Mode 1: High security mode. The car only starts and stays running with the RFID fob in range.
Mode 2: Medium security mode. The RFID fob must be in range for car to start and will stay running until the operator turns it off, then it won’t restart.
Mode 3: NO security mode. Should your fob become lost or damaged you can over-ride the system by entering a code with the hidden button switch.
The RFID is capable of working between 5 and 200 feet with the vehicle’s windows closed. If the vehicle’s windows are open we do not have a measurement for how far away the unit will work. There are 8 increments of sensitivity that the unit can be programmed to.
SKU: WI-RFID
Related products
-
Wire Routing for Hot Rods
Nylon and Billet Door Wire Looms (TP-NYLON-1/2)
The look of Billet & Black, the door looms are 1/2″ O.D. x 3/8″ I.D. x 7+” effective length. 1 One fixed and one sliding aluminum boss. Plastic lined. 1 Mount into 3/4″ and 5/8″ Diameter holes with set screw secured “quick” collars.
SKU: TP-NYLON-1/2 -
Remotes & Keyless Entry Systems
StreetWorks Door Solenoids (L22N)
You want more power. You want fast action. StreetWorks Solenoids have it. They work the way you want, with 40 pounds of pull so they work with original latches. Solenoids, cables, pulleys, connectors, wire hardware and instructions. Solenoid and bracket measure approximately 2-3/4″ wide x 2-1/16″ high (thick) x 4-1/4″ long.
If you need more power than these solenoids have, you have a door problem.
SKU: L22N
